Eurogrip 1500

Description

product image :: anti-skid coating used for car park High friction coating for pedestrian areas including bridges and ships decks that require an improved level of slip resistance.

Safety has never been more important and the public's awareness never so high. There is a need to both incorporate high friction surfaces into new works and to carry-out improvements to existing surfaces. Any surface is inevitably degraded with time and a thin coating of Eurogrip 1500 can be used to regenerate resistance to slipping.

The Eurogrip 1500 system combines tough but flexible polyurethane resins with highly abrasion resistant grit, calcined bauxite. Unlike many systems Eurogrip 1500 cures very quickly. Disruption is therefore minimal and a surface can be returned to full use in about 3 hours depending on temperature. It also cures at low temperatures, has excellent adhesion qualities and does not embrittle with age.

Benefits

Benefits include:

Long service life compared with other similar systems
Cold applied using only a roller
Low hazard materials
No need to remove road markings
Resistant to oils and solvents
Minimal maintenance
Minimal traffic disruption
Suitable for a wide range of substrates (bitumen, concrete, timber, steel, etc)
Low initial and whole life cost

Return to TOP of page

Application

Ambient temperatures should be between 5 and 30^oC during application and cure. Dry weather conditions and a dry substrate are essential. For low temperature application onto a sloping surface contact Optus.

Preparation of Substrate

STEEL

Remove all rust, mill scale and surface contamination by grit blasting and other mechanical means to a bright rust free surface (SA2½).
Remove oil and grease contamination with a suitable cleaning fluid and flush off residue with water.
Allow to dry thoroughly.

For other non ferrous metals – refer to Optus.

PRIMING

Prime immediately with Europrime FM following surface preparation.
Allow to cure tack free (on average 2 hours).
Eurogrip should then be applied during the following 10 hours, failing which the area should be reprimed.

Surfacing (Base & Aggregate Scatter)

Strict compliance with the mixing and laying procedure is critical – mixing times must not be exceeded.

Materials include Eurogrip 1500 which comes as 2 components. It is used in conjunction with the customers chosen aggregate.

Pour the contents of Pack B into a suitable mixing vessel and mix using a drill and paddle until homogeneous. Whilst still mixing, add the contents of Pack A and continue mixing for a further 20 seconds.

Roll the mixed material onto the surface to the specified coverage (do not spread too thinly).

Broadcast the chosen aggregate onto the surface ensuring that there is no resin showing through.

Remove any tape when resin starts to gel and excess aggregate when the surface becomes stable. This will vary with both product and ambient temperature.

Return to TOP of page

Coverage/Cure Rate

Both coverage and cure depend on ambient and surface temperatures, the type and condition of the substrate and the aggregate temperature and size.

Eurogrip 1500 must be laid at a coverage between1.3 and 1.5kg/m².

Grit loading varies with the chosen aggregate size and type. Typically for a 0.9 to 1.4mm grit it would be 5kg/m².

Note: Always ensure that there is always excess aggregate available on site to achieve full coverage prior to sweeping.

Grit is available in a range of natural colours and sizes.

Curing times

Initial set @ 20^oC: 1 hour
Open to traffic @ 20^oC: 2½ hours

Typical Properties

Relative density at 20^oC: 1.44

Tensile properties to BS 2782 Pt3 after curing for 14 days in air:

Tensile strength 8.0kN/m²
Elongation at break 125% min

Adhesion properties to BS 24624:1993, pull-off test at 5 days:

To timber , substrate cohesive failure at 2 kN/m²
To concrete, substrate cohesive failure at 2 kN/m²
To bitmac, substrate cohesive failure at <2kN/m²
To steel 6kN/m²

Packaging

Eurogrip 1500 is supplied in 10kg units and in 2 components. Packaging is 2.5ltr pot (pack A) and a 10ltr pot (pack B).

Health and safety

Refer to Health and Safety Data Sheets for each component of this product.



Quick Contact Details Tel: 0151 604 0001 Fax: 0151 678 2819 Email: info@optus.co.uk Browse Marine Eurogrip Marine Eurogrip STS Eurogrip 1500 Eurogrip 125 Euroscreed Optideck Leisure Trawlerdeck Featherdeck 90	Eurogrip 1500 Description High friction coating for pedestrian areas including bridges and ships decks that require an improved level of slip resistance. Safety has never been more important and the public's awareness never so high. There is a need to both incorporate high friction surfaces into new works and to carry-out improvements to existing surfaces. Any surface is inevitably degraded with time and a thin coating of Eurogrip 1500 can be used to regenerate resistance to slipping. The Eurogrip 1500 system combines tough but flexible polyurethane resins with highly abrasion resistant grit, calcined bauxite. Unlike many systems Eurogrip 1500 cures very quickly. Disruption is therefore minimal and a surface can be returned to full use in about 3 hours depending on temperature. It also cures at low temperatures, has excellent adhesion qualities and does not embrittle with age. Benefits Benefits include: Long service life compared with other similar systems Cold applied using only a roller Low hazard materials No need to remove road markings Resistant to oils and solvents Minimal maintenance Minimal traffic disruption Suitable for a wide range of substrates (bitumen, concrete, timber, steel, etc) Low initial and whole life cost Return to TOP of page Application Ambient temperatures should be between 5 and 30^oC during application and cure. Dry weather conditions and a dry substrate are essential. For low temperature application onto a sloping surface contact Optus. Preparation of Substrate STEEL Remove all rust, mill scale and surface contamination by grit blasting and other mechanical means to a bright rust free surface (SA2½). Remove oil and grease contamination with a suitable cleaning fluid and flush off residue with water. Allow to dry thoroughly. For other non ferrous metals – refer to Optus. PRIMING Prime immediately with Europrime FM following surface preparation. Allow to cure tack free (on average 2 hours). Eurogrip should then be applied during the following 10 hours, failing which the area should be reprimed. Surfacing (Base & Aggregate Scatter) Strict compliance with the mixing and laying procedure is critical – mixing times must not be exceeded. Materials include Eurogrip 1500 which comes as 2 components. It is used in conjunction with the customers chosen aggregate. Pour the contents of Pack B into a suitable mixing vessel and mix using a drill and paddle until homogeneous. Whilst still mixing, add the contents of Pack A and continue mixing for a further 20 seconds. Roll the mixed material onto the surface to the specified coverage (do not spread too thinly). Broadcast the chosen aggregate onto the surface ensuring that there is no resin showing through. Remove any tape when resin starts to gel and excess aggregate when the surface becomes stable. This will vary with both product and ambient temperature. Return to TOP of page Coverage/Cure Rate Both coverage and cure depend on ambient and surface temperatures, the type and condition of the substrate and the aggregate temperature and size. Eurogrip 1500 must be laid at a coverage between1.3 and 1.5kg/m². Grit loading varies with the chosen aggregate size and type. Typically for a 0.9 to 1.4mm grit it would be 5kg/m². Note: Always ensure that there is always excess aggregate available on site to achieve full coverage prior to sweeping. Grit is available in a range of natural colours and sizes. Curing times Initial set @ 20^oC: 1 hour Open to traffic @ 20^oC: 2½ hours Typical Properties Relative density at 20^oC: 1.44 Tensile properties to BS 2782 Pt3 after curing for 14 days in air: Tensile strength 8.0kN/m² Elongation at break 125% min Adhesion properties to BS 24624:1993, pull-off test at 5 days: To timber , substrate cohesive failure at 2 kN/m² To concrete, substrate cohesive failure at 2 kN/m² To bitmac, substrate cohesive failure at <2kN/m² To steel 6kN/m² Packaging Eurogrip 1500 is supplied in 10kg units and in 2 components. Packaging is 2.5ltr pot (pack A) and a 10ltr pot (pack B). Health and safety Refer to Health and Safety Data Sheets for each component of this product.

HOME \| INDUSTRIAL FLOOR COATINGS \| ANTI-SKID COATINGS \| DECORATIVE SURFACING \| SPECIALIST MARINE \| SITEMAP \| CONTACT US